Using a Cart
When horses were the main source of power on every farm, in the British Isles it was the tip cart, rather than the waggon which was the most common vehicle. The reasons for the cart’s popularity were many; it was simple in construction and therefore cheap, it can tip its load on to the ground, saving time in handling, and it is very manoeuvrable in narrow lanes and farmyards.
The tip cart varied in size to suit the local terrain and was known by different names in different parts of the country- muck cart, scotch cart, tumbrel or putt, amongst others, some names belonging to a particular style of construction; but they were all similar in their basic design: two wheels, a tipping body and shafts.
A young Percheron mare with a cart load of muck.
Putting the cords over the top of the hame to keep them safely out of the way.
Cart Harness
The shafts and the harness for the tip cart differ from that used for lighter vehicles intended for road use, because of the greater forces exerted upon them. The shafts are thicker, and the harness is stronger, using steel chains where necessary. The shafts are held up by the back chain (or ridger), which lies in a groove in the cart saddle, and is attached at each end to hooks on the shafts. These hooks slide along a long staple which is bolted through the shaft. The front of the staple has another hook to attach the shoulder chain (or tug), with a third hook at the back to attach the britchen chain.
The cart saddle rests on the horse’s back, where a riding saddle would sit. It consists of a saddle tree, two boards of beech or elm wood, joined by the wooden bridge, which has a metal-lined groove for the back chain to lie in. The boards need to be far enough apart to prevent pinching the horse’s spine and the cart saddle is wide enough to keep the chains away from the horse’s sides. The boards have pads underneath of cloth filled with straw, and these rest on the horse’s back. The top of the boards is covered in leather and the girth strap is nailed to the boards. There is a strap at the back to buckle onto the britchen and buckles at the front for the meeter straps, which come from the collar. These prevent the collar sliding forward if the horse puts his head down.
The britchen consists of a breech band, three to four inches wide, made of two or three thicknesses of leather, with hip and loin straps to keep it at the right height. Joining hip and loin straps and lying above the horse’s spine, is the crupper, the front end of which buckles onto the cart saddle. Although it is called a crupper it does not go round the horse’s tail, having only a very small loop at the end which has no practical purpose except maybe hanging it up. At the ends of the breech band are chains to hook onto the shaft hooks. The cart saddle and britchen are usually left buckled together when not in use.
The bridle and collar are the same as are used when working in traces, the hames being provided with hooks for the shoulder chains. The final item of harness is the belly band, often a double thickness strap, about two inches wide, which buckles round each shaft. It only comes into operation when the shafts lift up when backing, when tipping the cart or when there is too much weight on the back of the vehicle.
Harnessing the Horse
When putting on harness, the collar and hames go on first, followed by the cart saddle and britchen. To pick them up, I put my left arm under the centre of the saddle with the long end of the girth pulled back over the top, towards my body; and put the crupper, between hip and loin straps, over my right shoulder. Walking up to the near side of the horse, I put the cart saddle on the horse’s back with both hands, then leaving my left hand to steady the saddle, centre the britchen over the back of the horse with my right hand. Then with both hands I lift the saddle up and forwards and slide it back into position with the lie of the horse’s hair, push over the girth, reach underneath and buckle it up. If the cart saddle has buckles on the front, the meeter straps from the collar are buckled up and the tail is pulled out of the breech band. Then the bridle goes on and the leather reins or rope cords (lines) are passed through the hame rings and tied or buckled into the bit rings, the remainder of the cords being neatly coiled over the top of the nearside hame. With the hame rein (sometimes, although incorrectly called the bearing rein) hooked over the top of the offside hame and making sure to bring a belly band and shoulder chains, if they are not already on the vehicle, the horse is ready to be hitched up.
Hitching up
There are two ways of hitching to an empty cart. The easiest way, especially when working on your own is when the shafts are left up in the air. The back chain should be hooked onto the shafts at both ends, and the belly band can be left on the offside shaft. The harnessed horse is backed underneath the shafts, and the shafts are carefully lowered over the horse and the back chain is laid in the groove in the saddle. If a halter is used under the bridle (as it is in my native county of Yorkshire) the waggoner (horseman, teamster) can keep hold of the halter rope whilst hitching, particularly if the horse is not used to what is happening. Then, starting on the nearside, the shoulder chain is hooked on to the hame hook. The waggoner then walks round the horse and hooks on the offside shoulder chain, then the offside britchen chain before walking back round to the nearside. He hooks up the near britchen chain and reaches under the horse for the belly band, and buckles it round the shaft. The waggoner is then in the correct position to tie up the halter rope and take the lines down from the top of the hame. For safety reasons the shoulder chains are always hooked up first and unhooked last so if the horse moves forward, the cart goes with him.
Hooking up the shoulder chains. I am holding the chain, keeping the last link rigid between thumb and first finger so I can hook it on without getting a finger behind the hame hook, in order to avoid getting a squashed finger if the horse should move. Notice the end of the halter shank (lead rope) coiled up, out of the way.
The horse in the shafts. The back chain is at an angle, but should become vertical when the horse leans into the collar. This is adjusted by lengthening or shortening the shoulder chains. I have not used the last two links. If the chains had been at full length it might have been possible for the end of the shaft to get trapped behind the collar when turning. This belly band is made of webbing, instead of leather, and is tied together.
To check that the shafts are in the correct position, the back chain should be vertical when the shoulder chains are tight. This can be adjusted by using fewer links of the shoulder chains. The shoulder chains should be the same length on each side to equalise pressure on the collar and the horse’s shoulders. The height of the shafts is adjusted by dropping links of the back chain so that the top of the shafts is about four inches below the hame. This allows the line of draught to pass from the hame, along the shoulder chain in a straight line through the centre of the wheel. The britchen chains should be made tight enough, by dropping links, so that the cart doesn’t run forward much before being held back by the britchen. The belly band should be loose under the belly so that a flat hand can be put under it, but not so loose that a horse could get its back foot over it, if kicking at a fly.
Un-hitching is the exact reverse procedure, making sure that the britchen chains hang inside the shafts and the shoulder chains, if left on the cart, are outside the shafts, so they don’t get caught on anything as the shafts are pushed up in the air. Avoid letting the back of the cart bang on the ground. It is a good idea to keep the horse where he is for a moment before walking him forward, so he learns to wait while you check everything is clear.
Hitching up when the shafts are on the ground
The second method of hitching up, and the only method with some smaller carts, is when the shafts are on the ground. In this case the back chain is left hooked to the off-side shaft only and all the other hooks should be turned outwards, out of the way of the horse’s feet. The horse is carefully backed between the shafts, making sure he doesn’t stand on them. If there are two of you, each person lifts a shaft, the back chain is passed over the cart saddle and hooked on the near shaft by the other person. If you are working on your own you can hook up the off shoulder chain to keep the shafts up, pass the back chain over the saddle and hook it on, but I find the chain tends to slide back out of the groove in the saddle before I can get to the other side of the horse, which is why I prefer to start with the shafts up in the air. The shafts can be held up by looping the shoulder chain round the off shaft and hooking both ends on the hame hook, until the back chain is fastened. Alternatively, if the shafts have prop sticks, one of them can be let down to hold the shafts while the back chain is hooked on. The procedure is then the same as before, shoulder chains first, then the britchen chains and the belly band.
Un-hitching is the same as when the shafts were in the air, except the back chain is unhooked at the near side before lowering the shafts to the ground, without dropping them and frightening the horse. Check all is clear from the horse’s feet and that all hooks are turned outwards before leading him forward.
Driving a horse and cart
Ready to go. The driver’s position when walking. The extra length of cords is coiled and kept away from getting tangled in the feet.
When driving the horse from the ground, the usual position is to walk level with the horse’s flank, keeping aware of obstacles on both sides, as well as your own position relative to the cart, particularly when turning the horse towards you or when going through a gateway. Pay attention to your position relative to the body of the cart; it is all too easy to allow your hands to slip back down the lines and find the body of the cart knocks you from behind. When working in confined spaces, especially when backing, it is better to go to the horse’s head and steer him from there, having first looped the lines over the top of the hame.
When driving the horse from the ground, the usual position is to walk level with the horse’s flank, keeping aware of obstacles on both sides, as well as your own position relative to the cart, particularly when turning the horse towards you or when going through a gateway. Pay attention to your position relative to the body of the cart; it is all too easy to allow your hands to slip back down the lines and find the body of the cart knocks you from behind. When working in confined spaces, especially when backing, it is better to go to the horse’s head and steer him from there, having first looped the lines over the top of the hame.
When the cart is empty you can ride in it, either standing at the front or sitting on the side board. The safest way to get into the cart is over the front. Put your left foot on the back of the shaft and, keeping hold of the reins, pull yourself up with one hand on the crupper and the other on the top of the cart. If the horse should move, you still have contact with his mouth and can easily swing the other leg up into the cart. The other driving position is sitting on the front with your feet on the near shaft. This position can be useful when the loaded cart is tail-heavy and the shafts lift up against the belly band. It puts some weight on the shafts and helps the horse’s feet grip. However, if going any distance, it would be better to rearrange the load and walk. To check the balance of the load in the cart, it shouldn’t be a struggle to lift the front end of the shafts to take the weight off the back chain, nor should it be too easy as the cart will then tend to bounce about on the back chain.
Driving the cart from inside, the cords or reins passing in a straight line throught the hame rings to the horse’s bit.
The safe way to get in the cart whilst keeping control of the horse.
Tipping the cart
The great advantage of the cart over the waggon is its ability to quickly tip its load. Before tipping the cart, the tailboard is removed. Then the tipping lever, or other mechanism to secure the front of the cart body to the shafts, is released. The horse is backed up a step and the cart tips up. This happens because the very back end of the shafts, where they pivot on the cart body, is in front of, and usually higher than, the axle. Since the load on the wheels tends to act as a brake, the force of the horse backing pushes the cart body over. If the cart is front heavy it might need a bit of a push upwards at the front. As the horse moves forward the load slides on to the ground.
The position of the axle relative to the pivot point with the shafts also helps in getting the cart body back up into its travelling position, but because there is now much less weight on the wheels, there is not enough resistance to enable the pull from the horse alone to lift the cart body. So you need to assist. One method is to lift the tail of the cart whilst sending the horse forward a step. Another method, which lets you keep hold of the reins, is to push your right foot against the front of the nearside wheel and pull down on the front corner of the cart whilst sending the horse forward. When the cart body is back up again, it is secured to the shafts and the tailboard is replaced.
Getting the cart back into the travelling position. I am ready to put all my weight into pulling backwards and downwards against my foot, and give the horse the command to go.
The horse moves forward and the cart body comes up.
Leaving a loaded cart
If the cart needs to be left loaded and the horse taken away, some carts have prop sticks to allow this. There are three sticks, one under the back of the cart body, and one on each shaft. When not in use, the loose end of each of the front prop sticks hangs on a ring, which can slide along a staple in the underside of the shaft to allow the stick to be let down. [fig.1] The rear prop stick hangs on a large hook above the axle. To ‘set up’ the cart, both wheels are securely chocked at back and front, so they can’t move at all. The prop stick at the back is let down, angled backwards and pushed tight between the cart and the ground. Then the front prop sticks are let down, pulled out sideways and the bottom ends gently kicked inwards, towards the horse, to take the weight off the back chain. The horse is then unhitched as before, bel1ly band first, then the britchen chains, shoulder chains and the back chain. All the hooks should be turned outwards and the breeching chains dropped in behind the breech band to prevent them from catching on anything. Then the horse can be led slowly forward, checking everything is clear. It is a good policy to stop the horse when he is halfway out to make sure none of the harness is caught up. When the horse is out, the waggoner then walks between the shafts and then holding them up with his forearms, repositions the prop sticks with his feet so the bottom ends touch each other on the ground. This makes the cart more stable. Putting the horse back in the cart is the same procedure in reverse.
Although the cart was probably the main use for cart harness, many other vehicles and implements were made with shafts. Except for Yorkshire pole wagons, all other British wagons had shafts, as did most rollers, root drills, steerage hoes, hay turners and tedders so the cart harness was always in use.
This is a West Midlands style of cart saddle which is built up higher than the Yorkshire pattern. It has two girth straps, and buckles for the meeter straps from the collar. The leather belly band is only one thickness of leather as the horse is hitched to a hay turner which, unlike a cart, will not put any upwards pressure on the shafts. The shaft itself is also much lighter than a cart shaft.
This horse is hitched to a hitch cart. The cart saddle and breeching are a Yorkshire pattern without meeter straps to the collar, which in this case is an American one. The breeching here is at a good height for backing a load. The bridle is an open bridle, without blinkers.