Turning and Tedding Hay

Even if mowing hay with horses is a bit too advanced for you or your horses, turning the hay is much more straightforward. If you get someone else to cut and bale your hay, being able to turn it yourself still allows you to push on the drying process, and it is a useful job which you can often do with a single horse.

Unless it is a very thin crop, hay needs to be moved to allow the air and sun to reach the underside so it can dry properly. Before horse-drawn machinery was invented, hay was moved with a pitchfork or a hay rake, and the first horse-drawn machines copied the action of these tools. To turn hay using a hay rake the person stands to the side of a swath and pulls the rake towards them, lifting as they do so, which flips the swath upside down. In practise, working at a slight angle to the swath is helpful, and this is the way the horse-drawn side delivery rakes and the spider-wheel turners function. Another way of turning a swath is to flick it sideways with a fork, and this is how the Dickie turners work, the rotating tines continuously brushing the hay to the side.

Fluffing up the hay is known as tedding. When done with a fork, you can lift and shake the hay off, or you can flick the hay backwards in small amounts. This is how many hay tedders work, either the reel-type which have rows of sprung tines which usually rotate in the same direction as the wheels, or the fork-type tedders which have what look like a series of pitchforks which flick the hay upwards behind the machine.

Tedding hay with a horse-drawn tedder

A traditional reel-type tedder which throws all the hay out backwards.

Most horse-drawn turners and tedders were designed to be pulled by a single horse in shafts, but some models were made in different sizes to suit a pony, cob or draught horse. My tedder, for example, originally had shafts that were too short for a draught horse, and the horse was so closely coupled to the reel that plaiting up the tail to keep it away from the tines was a necessity.

On most hay machinery there are few adjustments; on reel-type tedders the angle of the tines can be adjusted to give more vigorous tedding which throws the hay higher in the air, though in my experience this is best done only when the hay is partly dry to avoid the hay getting wrapped round the bars. On machines which are driven from the wheels, there is a lever on each wheel to engage the drive, or a clutch to engage the mechanism. On the type of turners often known as a Dickie turner, though the name really applies to a Massey Harris machine, the two sets of tines can either turn in the same direction, each turning one swath sideways, or can be configured to throw both swaths inwards to make a larger windrow.

A side-delivery rake pulled by a Percheron mare

A side-delivery rake which rakes the hay sideways, thus turning it upside down.

On side delivery rakes, the height of the raker bars can sometimes be altered, so for a very thin crop which was cut close the soil you would set the tines low to the ground to ensure all the hay was moved. When putting two rows into one, the hay is pushed along in front of the whole length of the raker bars and emerges at the side, but to turn two swaths independently, the central section of each raker bar can be removed. This allows the left-hand end of the raker bars to turn one swath while the right-hand end turns another, though with long hay there is a tendency for the trailing end to steal hay from the other swath.

A later implement which turns the hay in a similar fashion to the side-delivery rake is the spider-wheel turner, the most common type being the Vicon acrobat which attaches to the hydraulic arms of a tractor. To use these implements behind horses requires a hitch cart with hydraulic arms and enough weight in front, ideally with an additional axle, to balance the rake. Earlier incarnations of this tool, however, ran on three wheels and were designed to be used behind a tractor or a horse, the version made by Lely in the Netherlands often having a hook at the front to attach a swingletree. The spider-wheel rakes have no drive mechanism; they simply turn by the ends of the spider wheel tines engaging with the hay or with the ground. The height can be altered by turning a handle which raises each row of spider wheels; set it too high and some hay will be missed, set it too low and the draught is greatly increased. The other factor affecting the draught is the angle the wheels meet the hay. If the spider wheels are set at a shallow angle to the direction of travel, the wheels give a glancing blow to the hay as they turn, whereas when the rake is adjusted so the wheels meet the hay more square on, the draught is much greater and the hay is thrust more vigorously sideways and rotated more, tending to twist it together.

Using a spider wheel rake and a Percheron horse to turn hay

A single horse pulling a Lely spider-wheel rake, the seat and shafts having been added for use with a horse.

Using a spider wheel rake and a Percheron horse to turn hay

The same rake, but with all the wheels in line to put two rows into one, this time with a pair of horses in a hitch cart.

There are pros and cons to all these implements, the spider-wheel rakes stop turning at the ends of the swaths when you turn in the direction of the windrow and tend to lump the ends together, but they don’t block up and have few moving parts. The side-delivery rakes on the other hand, do keep turning the hay at the ends, but have a lot of moving parts and it is hard to find new tines when the old ones break. You also need to keep the tines smooth and free of rust to prevent the hay being lifted and jamming the mechanism.

In tractor farming, most hay nowadays is spread by a tedder having two or more rotors which turn around a near-vertical shaft, each sweeping a semicircle of hay ahead of them and chucking it out of the back. The Hay-bob and Fahr centipede are typical examples. The advantage of these machines is that each pair of contra-rotating tines overlap each other, thus pulling apart any clumps before throwing it out evenly behind. Having the hay spread over the whole width of the machine, rather than in rows, does allow the sun to dry the grass more quickly, but there are some disadvantages too. If there is clover in the crop, the leaves which contain much of the nutrients are likely to be knocked off by the tedder’s aggressive action, and the machines require quite a lot of power. Although designed for tractors, they can be pulled by horses with a hitch cart. The most common two-rotor models in Britain are mounted implements, so need to be lifted by the hitch cart as well as being powered by it. This requires a hitch cart of sufficient weight to outbalance the tedder, and usually an engine to power the machine. There are some tedders which are trailed, which solves the problem of lifting, generally a better solution with horses, but they still need to be powered. This can be accomplished with an engine, either mounted on the hitch cart or on the tedder’s drawbar, or by a ground-drive hitch cart. I have seen pictures of horse-drawn mowers converted to a ground drive hitch cart to power a tedder, and there are commercially built hitch carts which also serve the purpose. However, whereas a single horse would pull any of the traditional turners or tedders, it requires two horses to pull this type of tedder when using ground drive.

A ground-drive rotary hay rake

A new ground-drive rake made by I and J Manufacturing, which leaves the hay in a very even windrow ready for baling.

An engine-powered hay tedder pulled by two horses

A four-rotor tedder with an engine mounted on the drawbar behind a pair of horses and a basic hitch cart.

Wider machines, newer machines

For bigger acreages, the wider tractor-type tedders do allow quicker covering of the ground, perhaps with three or four horses, an important factor if you have a lot of hay to dry. The older style of machinery, with the exception of a new fork-type tedder, only works at the width of two swaths, so the only way of covering more ground using more horses is an extended steerable hitch to allow two rakes or tedders to be used behind one hitch cart.

A new reel-type tedder with a pair of horses

A modern reel-type tedder demonstrated at Horse Progress Days.

A fork-type hay tedder

A new and extra-wide, fork-type tedder, easily pulled by two Fjord ponies.

A final consideration if you use horse-drawn haying equipment is their compatibility with different widths of swath left by the mower. Most horse-drawn tedders and turners are designed for swaths of four and a half or five feet. But for a wider swath, particularly a ten-foot swath that might be left by a tractor, the side delivery and spider-wheel rakes would leave uneven lumpy rows, because they require a clear line between appropriately wide swaths.

Like any implements used with horses, there is a balance to be found between the available horse power, (whether literal or the mechanical imposter) and the available equipment, its capacity, design and draught requirements. Add to that the time available, the number of acres, the different crops, climate and topography, and the range of variables soon stacks up.