John Dodd and David Wise of Sillywrea Farm

In many ways, Sillywrea Farm is typical of an upland Northumbrian farm, cattle and sheep being the main enterprises. When I visited in 2005, I went to see their work with the Clydesdales horses and to find out how they ran the farm using traditional horse-drawn machinery. 

In the hills a few miles south of the Romans’ northern frontier at Hadrian’s Wall, a straight and narrow farm road drops gently down past a clump of trees, to the solid stone farm house and buildings of Sillywrea Farm. Most of the fields on either side are under grass, and typically for an upland farm, they are all enclosed by dry stone walls. The grass is grazed by a flock of 100 Cheviot and 80 Suffolk ewes and their lambs, a suckler herd of 25 cattle, and the Clydesdale horses which work the farm.

The farm has been in the Dodd family since 1848, and is now run by John Dodd and his son-in-law, David Wise. The soil of the farm is a heavy blue clay, not an easy soil to work, and in fact there are the remains of tile kilns in some of the fields. Though most of the 200 acres is under grass, some roots and cereals are also grown. The usual rotation has been two years of white crops, followed by a year of roots, then another two white crops, before the land is grassed down again. This year there were 17 acres of spring barley, and 4 acres of roots, which is a little less than normal. This year an experimental forage crop, which used to be grown in the area, has been tried. This mixture of oats and tares, with a little rye added, was grown on some of the damper land where it is a bit of a worry getting a combine out. It has proved to be a successful crop, producing a tremendous bulk of forage when made into hay. Cut when the leguminous tares were in flower, with the oats still green and the grain still milky, it will be a good source of carbohydrate and protein for the stock in winter.

The root land consists of a few rows of potatoes for home consumption, two acres of fodder beet, with the balance sown with swedes, some of which are fed in situ, others being lifted to feed to the ewes at lambing time. Some of the ram lambs from the Suffolks are kept entire and sold as shearling tups, whilst the young from the suckler herd are now sold as stores. The cattle are housed in tie stalls during the winter, and are mucked out into carts, the muck being spread by hand on the fields, ideally every day. The cattle are Simmentals, having been bred up over the last 40 years from an original population of Hereford/Friesian crosses. In fact, no sheep or cattle have been brought onto the farm in that time, apart from tups and stock bulls.

c

One of the Clydesdale geldings standing in front of the farm house. 

The Horses

This contrasts with the horses, none of which are home-bred. They are all geldings, and on the day of my visit there were six of them on the farm. “Too many,” John says, though the oldest one, a nineteen-year-old, was due to be sold after hay time. The youngest horse on the farm is four years old, so they really need to buy another foal. However, John points out, “we cannot possibly buy another foal until we have got clear of an older one, well really, we should have clear of two. I mean four’s any amount. Three used to be all we had at one time, a pair and an odd one. But you see, you could go to the mart every month, there was horse sales, but now you have to have at least four, you have to have a spare in case one goes lame or anything.”

In recent years the horses have been bought as foals, rather than two or three-year olds, so that John and David are sure of having a young horse to break to work when the time comes, as nowadays it can be difficult to find a 2 or 3 year old when you need one. Having them as foals also gets them used to the farm routine and being handled, as John explains. “The first winter, we turn them out through the day and bring them in at nights, and what a good that does. We never just drive them, we always halter them and lead them in and lead them out in the morning, unless it’s a stormy day. They never forget that first winter, being led in and out, and caught first of all.”
When the horses reach their late teens, when a full day’s work would be too much, they are often sold. Besides making space for a younger horse, this also gives the new owner the benefit of working with a good reliable horse.

All the harness on the farm is traditional, and as John says “has a bit of age on it.” English cart harness is in constant use, much of the work being done with a single horse, the rest being done with a pair. Pairs are always worked with a collar, backband and chains, though John says it would be useful at times to have britchins when using a mower on some of the steeper banks. The ploughing is done with a general purpose Ransomes RNDH, using a YL point, which although not made for the plough, does fit it. Ploughing continues throughout autumn and winter, and then in spring the root land gets its second ploughing.

John Dodd ploughing

The ploughed land is worked down with a trailed spring tine cultivator which although made for a tractor is exactly like the horse ones, and zig zag harrows. Then John and David use a scrubber, a rarely used tool nowadays. It consists of a number of boards fixed together, and angled upwards in the direction of travel, like the levelling board on the front of a Dutch harrow. The bottom edge of each board which gets the most wear is reinforced with metal, as are the longitudinal boards on the top which hold the whole thing together. When the scrubber is turned upside down these boards function as sledge runners for transporting the implement between fields. For the scrubber to break the clods down effectively, the soil condition needs to be right; if it is too soft, the soil balls up, and if too hard, then it rolls around like cobble stones.

spring-tine cultivator

A set of spring-tine cultivators.

A horse-drawn scrubber

The horse-drawn scrubber.

The corn is drilled with a pair of horses on a Massey Harris drill which has 13 disc coulters, or a slightly larger one, which has 14 coulters. Although John and David don’t use a roll before drilling, they do use a flat roll after the corn is drilled and on grassland, one of the rolls being made by the Scottish firm of Sellars. To spread fertiliser a single horse is yoked the shafts of a 7 ft fertiliser spreader, of an unknown make, which has saucers and flickers to distribute the granules.

Spraying is a tractor job, done by a contractor, as is combining the crop. Since there isn’t a tractor on the farm, David borrows a tractor and trailer to lead the corn, which is bagged off immediately to store it until needed. The other tractor job is baling hay and straw. This used to be done by a contractor, but when he stopped baling small bales, David bought a baler and borrows a tractor again to drive it.

Whilst the land for cereals is worked in the usual way, because of the need to get a fine seedbed on the clay, the root land is worked twice, as David explains, “with the roots, the land is ploughed in the winter and just left. Then come spring, it’s worked down with spring tooth harrows, harrows, and scrubber and then ploughed again, stirring is what we call it, and then worked down with whatever implement.” After that the land is put into ridges, or drills as they are called in this part of the country. There are two drill ploughs (ridging ploughs) on the farm. The older one is a Grampion, bearing the dealer’s plate of ‘Paxton and Sons, Pity Me, Durham.’ This plough has a wheel on a screw thread between the stilts to adjust the width of the plough, whilst the newer plough, of an unknown make, has a small handle on a thread to do the same job. After being put up into drills, the fertiliser is spread and then the ridges are split. When the ground is dry enough, the roots are sown on the 28” ridges with a two-row bobbin drill made by Wm. Elder of Berwick.

Drill plough

The ‘drill plough.’

Bentall gapper

The Bentall root gapper.

To gap the roots, a single row gapper made by Bentall, is used behind a single horse. It has a pair of discs which go on either side of the plant which throw the soil and weeds away from the row. The drive for the gapping mechanism comes from two bevelled drive wheels at the front which grip the side of the ridge. The power is transferred via bevel gears to what look like propeller blades at the back. The first ‘propeller’ cuts across the top of the ridge and the second one knocks out the soil behind, and any plant that is there. Subsequent weed control is by cultivation, using a Scottish built scuffler, by Pollock, working a row at a time with one horse.

Whereas the fodder beet is pulled by hand and loaded into carts with a fork, the swedes are lifted with a turnip lifter made by Parmeter of Tisbury in Wiltshire. This one-horse tool has two converging blades parallel to the ground which gradually narrow as the tool travels forward and chop off the leaves, at least in theory. Sometimes though, the blades lift up and allow the leaves to pass underneath. For the tool to work well, the swedes need a good neck between the leaves and the root. If it works, the leaves continue to move down the platform formed by the blades, and are carried off to one side. An L-shaped tine at the back of the implement then cuts the root and pushes the swede out of the ground. The few rows of potatoes are planted with a single row planter by Wallace of Glasgow, and when ready to lift are almost invariably spun out of the ground with a Blackstone’s no.1 digger.

Being largely a grass farm, hay time is an important part of the year, about 50 acres of hay being made each year. They are various mowing machines on farm, Bamfords, Albions, and two locally made mowers made by Simms of Newton, near Corbridge, who specialised in making mowers and saw benches. Nowadays, they use the Albions, made by Harrison MacGregor of Leigh near Wigan, of which they have several, allowing them to swap parts between machines. The model they use is the 16R, which is one of the later ones, having its gears running in an oil bath. Because of the importance of the hay crop and the scarcity of working mowers, John says, ‘we never have to miss a chance of a good mowing machine, especially an Albion oil bath.’ As with any traditional sickle bar mower, cutting heavy or laid crops can be difficult and sometimes the field will need to be cut all one way.
To turn the hay, they usually use Massey Harris dickie turners, preferring them to the side delivery rakes which they find tend to wrap up in a heavy crop. They also use a three wheeled turner made by Blackstone, which works in the same way as the dickie turners. The hay is turned until dry enough to be put into windrows for baling. Although they do have a hay tedder, also a Blackstone, they only use it if they get caught out by rain after the swaths have already been put into the windrow for baling, and need to open them up to let them dry out again. After baling, the bales are stooked in the field on their ends in the traditional manner, with the knots down and to the outside, so if it does rain they take little harm. Then they are led to the barn on hay bogies, one of which was bought new by John’s father when John was a boy. Originally built for carting piked hay, 24 to 28 bales are loaded onto these low vehicles to lead them to the barn. Although in Yorkshire and further south this job would have been done with rulleys, consistent with the North Country tradition, John believes the four wheeled vehicle would be too big and heavy on this heavy land.

Tradition is certainly a significant feature of the work on Sillywrea farm. Many of the tools originated in Scotland or the north of England, with a number being made within a few miles of the farm. Apart from the few jobs which are done with a tractor, all the implements are traditional horse-drawn tools, designed to be used with horses; there are no modified tractor implements or hitch carts here. This approach definitely has some advantages; no time is taken up working out how to modify tractor tools, and anyway, the horse implements do not have the extra weight of tractor implements and are cheaper to buy and maintain. The initial cost may not seem that important, but it can effect things later on, as John relates, “I have known a lot of farmers who had no bother buying and changing over to the tractor and the machinery, but the bother came when they were to renew. The farms weren’t big enough to circulate plenty of capital for to get the second lot, and that’s what’s helped do away with a lot of family farms.”

Of course, there are also disadvantages in using old horse drawn implements, notably the lack of spare parts. Added to that, you can’t just go down the road to your local machinery dealer and get a new machine. John and David get round this problem by taking good care of what they have, buying machines for parts, and repairing things as soon as it is necessary. A small example of the care they take is the root gapper, which I was unable to take a photo of, until David untied a bag from its handle. The bag contained a spare part, ready to be put on when needed, rather than having it lying about somewhere and forgotten. This attention to detail is a reflection of John and David’s enthusiasm for using, maintaining, and when necessary, restoring their machinery.

For the more important tools which are needed at busy times, there are complete replacement machines, so if one of the two mowers out mowing should break down, another can be brought out of the shed to keep the job going until night. That is the reason their implement shed is absolutely stuffed full of machines, and why they keep a close eye on the sales looking for useful implements. Inevitably finding implements is getting harder, and at the moment they could do with more knives and knife sections for their Albion mowers.

As much as any of the farms in this series, Sillywrea could be seen as coming close to some idealised view of the farming of yesterday, but to think that would do John and David a disservice. Although they do much of their work in a traditional manner, they nonetheless are farming in today’s climate. The cows still need mucking out, the DEFRA forms still need filling in, and the books need to balance. In that context, their choice to use contractors for jobs like spraying and combining the barley is an entirely practical decision, which gets the job done and avoids the hassle and cost of investing in little-used equipment. Although other farmers who have tractors make very similar choices, for John and David it has a greater value, in that they can avoid having a tractor and its associated implements altogether. Besides wanting to do the work with horses, they are not torn between using one source of power or the other, so the horses are in daily work, which is the best way to keep them handy and fit for the next task. On a farm it is very easy to let things get too complicated. John and David’s choice to work in the way they do, avoiding unnecessary complication, allows them to concentrate their efforts on the sheep, the cattle, and of course, working their Clydesdale horses.