One of the first real jobs that many people do with their horses, and often the first job a young horse learns to do, is to harrow. There are good reasons for this – accuracy is not essential and there are no adjustments to be made to the implement so the horseman can fully concentrate on driving the horses. Although harrowing is usually considered an easy job, there are things you need to be aware of. Let’s start with the horses, and presume you have a pair of experienced horses, though you can also harrow with one, three, four or more horses.
The first consideration when doing anything with horses is to control their movement. I always have halters under the bridles, and use the halter shanks (lead ropes) to keep the horses level, by tying each halter shank to the other horse’s hame ring or to a dropped link on the trace (with American harness you can use either the top hame ring or for harrowing I often use the lower hame ring where the back strap from the breeching is attached to the hame.) I also use a coupling band, a short piece of cord between the inside bit rings of the horses, so the pull from one rein passes through one horse’s bit, along this coupling band, to the other horse’s bit. By changing the length of the coupling band and the halter shanks you can adjust the distance between the horses and keep a fast horse level with the slower horse without pulling on its mouth.
Three horses tied together with coupling bands from bit to bit and their halter shanks tied back to their neighbour’s hame ring.
A single horse with light harrows. The cords to the driver pass through a dropped link from the hame hook, so the cords pass in a straight line to the driver’s hands.
In other parts of the country people do not use halters under the bridles. Some only use a coupling band and do not tie one horse back against the other at all, whilst others tie each horse back by a length of cord from the bit ring, rather than a halter, to the other horse’s hame hook or dropped trace link, sometimes with a coupling band between the bit rings and sometimes without. The disadvantage of this method is that the fast horse is pulled by its mouth in towards its mate, unless you keep pressure on the cord, which is hard on the horse’s mouth and the driver’s arm.
The steering and stopping mechanism is completed with the usual hemp plough cords, each tied with a bowline to the outside bit ring of each horse, which then goes back to the driver’s hands. Hemp is the preferred material as it is the strongest of the natural fibres, it is not stretchy, and unlike manmade fibres like polypropylene, it does not burn your hands if it passes through your hands quickly. Between the bit and the driver’s hands it is usual to pass the cord through a ring on the horse’s harness. Some back bands have a ring sewn into them especially for this purpose, whilst some harness with a crupper has an extra hip strap with a ring for the cord to pass through. Otherwise it is common to thread the cord through a dropped trace link under the hame hook (or with American harness I clip an extra ring onto the lower hame ring and pass the cord through that.) All these methods allow the cord to pass in a reasonably straight line between hands and bit, which gives a better feel of the mouth and requires less pressure than passing the cord through the upper hame ring, which is what you use when driving from a vehicle. Having the cords passing down the sides of the horses, rather than over their backs, also means that if a horse moves its backside out sideways, as long as you keep hold of the rein, it is putting pressure onto its own mouth, so pulling it in line again.
The cords should be long enough so you can walk with your hands near your body without any risk of walking on the harrows, allowing enough length so that when the horses are turning and you are at the corner of the harrows you still have enough extra length to go round the far horse’s back end without you having to extend your arms or stand on the harrows.
Yoking up (hitching up)
Once your horses are fastened together you can drive them into position, just missing the corner of the harrows as you line them up in front of the swingletrees. Then slow them down or stop them, and turn them so that each horse is standing immediately in front of its own swingletree. You might have to back them a step or two. Then, with your cords in hand at all times, hook up the inside trace of the most reliable horse, then step back and hook on the outside trace. Especially if your horses are wearing blinkers, keep talking to them so they know where you are. Then go around the back of the harrows, adjusting the cords so you could easily stop the horses should they move, and hook on the inside trace of the other horse, then the outside trace. Yoking up in this order minimises the chances of the horses moving the harrows before you are finished, and it gives you a clear route out of the way if they do. Unhitching is the same procedure in reverse. Once you have made a quick visual check to make sure everything is as it should be, off you go.
As the horses move forward, the traces tighten, lifting the swingletree behind each horse, and the cobbletree (mastertree or doubletree) which balances the pull from each swingletree. From the centre of the cobbletree, one or more lengths of chain connect with a piece of steel or wood called the harrow baulk, onto which the sections of harrow are attached with hooks and short lengths of chain. Normally the width of harrows is greater than the width of the horses, so the horses do not need to be yoked close together.
When driving, it is customary to walk behind one edge of the harrows, so you can line it up with the soil moved on the last pass. Although it is not essential to drive straight, precise driving was always seen as a sign of good horsemanship, and it is good practise for more exacting jobs such as drilling or hoeing. Good driving also minimises the time it will take to do the job. The trick when doing field work is to steer the horses as little as possible and to gently adjust their direction, keeping an eye on their front feet and heads, because where the head leads, the body follows.
When moving ahead the crossed halter shanks tigthen keeping the horses level and spaced apart, whilst the eveners are lifted off the ground and balance out the efforts of the horses.
Driving a pair with chain harrows, the driver having lines long enough to walk at a safe distance behind the harrows and walking to the edge of the previous bout to keep the horses straight.
Turning the horses
Turning at the end of the field is where you particularly need to pay attention. If you or one of the horses are new to driving, turning in a wide arc is sensible to begin with, but soon you should aim to turn tight enough so the edge of the harrows almost turns on the spot, so you are in position to go back down the field next to the previous harrowing.
To do this, the horses need to slow down, and to some extent, step sideways. There does, however, need to be some forward motion. If you do not do this, when the horses turn too tight, a number of things can happen. If the harrow baulk is pulled sideways, the harrow sections may ride up over each other, which is inconvenient as you have to lift them clear from each other, or the horses may step over a trace, or even step on the harrows.
Starting the turn. The offside horse (nearest the camera) is a a little ahead of the nearside horse, so needs to be held back whilst turning to the right.
As the horses continue their turn, the harrows are starting to concertina up on themselves, but should flatten out as the horses complete the turn and move forward again.
If a horse gets a foot over a trace, this should be a minor inconvenience, (your horse should already have been to accept this happening) and is just the sort of thing that happens in day’s work. Stopping horses mid-turn and going to sort it out puts you just in front of the harrows, so it is usually better to finish the turn and get everything facing in the same direction before going in front of the harrows, shortening the cords as you go to keep contact with the horses’ mouths, and lifting a leg or re-hooking the trace.
If one of your horses turns too tight and steps on the harrows, there are several possible outcomes. The horse may just push the harrow further into the ground and then step forward, as horses don’t like to stand on things. A worse situation would be if the horse put its foot through a gap in the harrows and lifted the harrows as it lifted its foot. If the harrow fell off immediately, there may be no problem, but the last thing you want is a horse kicking with a harrow stuck on its leg. This is a typical example of where good preparation in the horse’s early training pays dividends, because a horse should go forward when it is told to, and it should stand still even with something around its leg. (Most trainers, before going near any implement, deliberately put a rope round a horse’s foot in a safe environment, so he gets used to having its leg movement restricted, and later purposely arrange for the trace to go between the horse’s legs. If you don’t understand how and why to do this in detail, don’t try it until you do.)
Intentionally turning the horses too sharply to show how the baulk has caught on the ground and is starting to flip the harrows upside down. Stopping the horses, and turning them to the right should allow the harrows to go back down. Especially with a wide set of harrows there is a danger of the cords getting trapped under the unpturned harrows.
Another possible outcome of turning harrows too tightly is flipping them upside down. This happens when the inside end of the harrow baulk gets caught on the ground or vegetation, and, with the draught chain at an acute angle with the harrow baulk, instead of pulling the harrows round, the draught chain pulls the far end of the harrows upwards. The dangers are that the horses don’t like the look of what is happening, that the harrows fall on top of the horses, and/or that your cords get trapped under the harrows.
All of these eventualities are avoided by not turning too tight. Warning signs are when the horse on the outside is going too fast, and, more particularly, when the horse on the inside of the turn side passes too much with slack traces, or steps backwards whilst turning, in which case it is better to send him forward, even if you end up with an untidy turn. With wide harrows such as seed harrows, you may need to start your turn quite tightly, with the horses heads up to the hedge, then straighten them out a bit as they go parallel to the hedge before turning tighter again to face back down the field.
There are essentially two types of harrows, chain harrows, and harrows with the spikes attached to a frame. These include seed harrows, chisel harrows, zig-zig harrows, and ducks’ foot harrows. Chain harrows are usually used on grassland, though I have, for instance, used them to harrow potato ridges and as seed harrows. Chain harrows are made of numerous sections of bent steel rods, each section being loosely attached to its neighbours. The tines which scratch at the vegetation and soil surface are usually formed from the ends of each small section. On some sets of harrows, however, the tines are separate, each pair of tines being twisted round a loop of one section, so the tines are loose and have very little effect. The purpose of chain harrowing is to pull out dead vegetation, to flatten mole hills, to spread manure and to open up the surface of the soil. In none of these actions does the chain harrow excel, and with time I am ever more inclined to think that on a well-managed and healthy soil the effect of a chain harrow is marginal. However, those who work horses tend to like chain harrowing, as it is useful to get a young or unfit horse into work, and it is something you can do at most times of the year when there may be little useful work to do. Although usually considered light work, the draught of chain harrows varies greatly, depending on the width, length, weight and construction of the particular set of harrows, and whether you are working tightly grazed or long, feggy or tussocky grass.
Spike tooth harrows are used mainly on arable land, to break down the land after ploughing and to make a seed bed. They come in a wide variety of weights, so a 10-foot set of light seed harrows for sandy land may be pulled by a single horse, whereas working on clay, a heavy set of chisel harrows, which have the ends of the tines bent forward and sharpened, may take all the horse’s effort to pull a two-foot wide section. The efficacy of these harrows and their ease of draught depends on many factors, the weight of the harrows, the angle and sharpness of the teeth, the type of soil, its moisture content, humus content and how much it has already been broken down. The ideal timing is when the soil has just the right moisture content for the clods to shatter under the harrow. Harrowing immediately after ploughing is probably the hardest work, especially as the horses must walk on the ploughed land, so rolling beforehand makes walking easier and allows the harrow tines to work more effectively. Spring harrowing an autumn ploughed field is much easier as the land has had time to settle and break down by natural forces.
Harrowing is good work for horses. Because the harrows work shallowly, a good amount of ground is covered and, on loosened soil, you do not need to rectify the compaction as when using a tractor. Moderately hard work, with a consistent load for the horses, harrowing is an ideal job for training horses to work steadily and to gain fitness, and for the same reasons it is pretty good for the horseman too!
Harrowing is good work for horses. Because the harrows work shallowly, a good amount of ground is covered and, on loosened soil, you do not need to rectify the compaction as when using a tractor. Moderately hard work, with a consistent load for the horses, harrowing is an ideal job for training horses to work steadily and to gain fitness, and for the same reasons it is pretty good for the horseman too!